Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Pasadena?
Replacing a gate motor and opener in Pasadena typically costs $850 to $1,900 for a residential swing gate, and $1,200 to $3,200 for a sliding gate operator. Repairing an existing motor, control board or access system usually runs $180 to $650, while a full new automated gate installation lands anywhere from $3,500 to $9,000 depending on the gate itself, the operator and the access controls. Every price below is a typical estimate for this market; the written estimate you get after we look at your gate sets the final number.
Gate Motor & Opener Cost Breakdown (2026)
Here’s how the numbers break out across the jobs we handle most in Pasadena. Motor and opener work is our specialty, not a side line, so these ranges reflect what a dedicated gate technician actually charges rather than a general handyman’s guess.
| Job | Typical Cost in Pasadena | What’s Included |
|---|---|---|
| Motor / opener diagnostic | Free with estimate | On-site inspection, testing the motor, board, sensors and wiring |
| Motor or operator repair | $180 – $650 | Motor, gearbox, limit switch or control board repair |
| Control board replacement | $280 – $700 | New board, reprogramming, testing the access inputs |
| Access system repair (keypad, remote, intercom) | $150 – $550 | Keypad, receiver, remote programming or entry wiring |
| Loop detector / safety sensor repair | $220 – $600 | Vehicle loop, photo-eye or safety-edge replacement |
| Residential swing gate operator replacement | $850 – $1,900 | New operator, mounting, connections, calibration |
| Residential sliding gate operator replacement | $1,200 – $3,200 | New slide operator, rack, wiring and safety sensors |
| Commercial operator replacement | $2,200 – $5,500 | Heavy-duty operator for HOA or commercial gate |
| Full new automated gate installation | $3,500 – $9,000 | Gate, operator, access control and site work |
What pushes a job toward the top of a range is almost always the operator’s age and the access setup behind it. A straightforward residential swing gate with a remote and a keypad is the low end. A commercial slide gate with a vehicle loop, an intercom and entry hardware wired to a building is the high end. The gate itself, not just the motor, matters too: a heavy ornamental gate needs a stronger operator than a light aluminum one, and that difference shows up in the price.
We work on your brand, whatever it is. Whether the gate is running a LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite or Mighty Mule operator, our technicians arrive familiar with the system on-site instead of guessing at it. That’s part of why diagnosis is faster here than with a multi-trade company splitting its attention. If you want the full picture of what we cover, start with Pasadena Gate Service.
What Affects Gate Motor & Opener Pricing in Pasadena
Two gates with the same problem can land at different numbers. Here’s what moves the estimate up or down.
- Operator brand and how common it is. A widely used brand is generally easier to work on because parts and know-how are everywhere. An older or less common operator can take longer to diagnose, which nudges the price up.
- Gate type and weight. Sliding gates carry heavier panels and need stronger operators than swing gates. A commercial-grade gate built for daily traffic costs more to automate than a residential gate opened a few times a day.
- Access controls on top of the motor. A keypad, remote, intercom, vehicle loop or card reader each adds a piece. Entry systems with more ways in cost more to repair and replace. Electrical wiring and power to the operator is a genuine safety point here: gate operators run on line voltage and store force in heavy moving parts, so we don’t talk homeowners through live-wire work. That’s a trained professional’s job.
- Whether it’s repair or replacement. Fixing a control board or motor is almost always cheaper than replacing the whole operator. We diagnose first and only recommend replacement when a repair won’t hold.
- Age of the existing system. A gate operator past its service life can develop several problems at once. When the motor, board and sensors are all failing, the math can favor a new operator over repeated repairs.
- Local conditions. Pasadena’s heat and humidity are hard on outdoor equipment. Moisture works its way into control boxes, and the summer sun bakes anything left out in the open. Operators and boards that live outdoors here wear faster than the same equipment in a cooler, drier climate, so we check seals, enclosures and connections on every visit.
How to Save on Gate Motor & Opener
The biggest lever on cost is catching a problem early. A motor making noise or a gate slowing down is cheap to fix now and expensive to ignore. Here’s what actually moves the number down.
- Get a free estimate before you commit. A written estimate tells you exactly what the job needs and what it costs. Call (855) 772-8171 and we’ll come out and price it.
- Repair before you replace. If the motor is sound and the board is the issue, fix the board. Diagnosis first, solution second. We don’t push a replacement when a repair will do the job.
- Service the brand you already have. Your installed operator is what it is. A brand-agnostic technician works with the system on-site rather than steering you toward a new brand for the sake of a sale.
- Fix the small access items together. A sticky keypad, a dead remote and a misaligned sensor cost more as separate visits than as one. Group them into a single call.
- Keep the gate itself moving freely. A gate that drags or binds makes the operator work harder and wears the motor out faster over time. A gate that swings or slides cleanly takes the load off everything behind it.
Why a Gate Specialist Costs Less Than a Generalist in the Long Run
Gate specialists, not generalists. That’s the whole pitch, and it’s a money argument as much as a skill one. A general handyman or a multi-trade company that handles gates on the side often can’t diagnose a specific brand’s control board or access system, so the first visit turns into guesswork. Sometimes a part gets replaced that didn’t need it. Sometimes the real problem gets missed entirely and the homeowner pays twice.
A technician who works on gates all day, every day, arrives knowing the systems. Our team is fluent across nine major gate brands, from LiftMaster and FAAC to DoorKing and Elite to Mighty Mule. Electric gate repair is a core competency here, not an add-on. We handle motors, control boards, loop detectors and access-system failures that stump generalists. That focus is why diagnosis is faster and the solution is more accurate than a company splitting its attention across a dozen trades.
From a stuck gate to a full installation, one call covers it. If your gate is failing and you want to understand the repair side in detail, our guide to electric gate repair walks through what goes wrong and how we fix it. If you’re weighing a new install against a repair, the gate installation page covers what a full build involves.
Repair or Replace: Which Costs Less Over Time?
Repair usually costs less when the motor is sound and only one component has failed. Replace when the operator is past its service life and several parts are failing at once, because repeated repairs stop being the cheaper path.
A single motor, board or sensor repair sits in the $180 to $650 range. Over a few years, though, a gate that keeps breaking can stack up several of those. When the repair bill starts approaching the price of a new operator, replacement makes more financial sense. We tell you honestly which side of that line you’re on. Diagnosis first, solution second.
Full lifecycle coverage means you never need a second vendor as your gate’s needs change. Today’s repair and next year’s install come from the same place. If you’re in Pasadena and weighing repair against replacement, that continuity is worth having.
What Happens When You Call
Call (855) 772-8171. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. When a technician arrives, they inspect the gate, test the motor, board, sensors and access controls, and figure out what’s actually wrong before quoting anything. The estimate is free, and the price is set per job by the written estimate. No mystery fees, no pressure to replace what can be repaired.
We’re closed on Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Our technicians have up to 15 years of experience, and they’re gate specialists first.
FAQs – Gate Motor & Opener Cost in Pasadena
How much does a gate motor replacement cost in Pasadena?
A residential gate motor replacement in Pasadena typically runs $850 to $1,900 for a swing gate and $1,200 to $3,200 for a sliding gate. Commercial operator replacement runs $2,200 to $5,500. The exact figure depends on the operator, the gate weight and the access controls. Call (855) 772-8171 for a free estimate.
Is it cheaper to repair or replace a gate opener?
Repair is usually cheaper. A motor or control board repair typically costs $180 to $650, while a full operator replacement runs $850 and up. Replace only when the operator is past its service life and several parts are failing together. Call (855) 772-8171 and we’ll tell you which makes sense.
How much does an electric gate control board or sensor repair cost in Pasadena?
A control board replacement usually runs $280 to $700, and a loop detector or safety sensor repair runs $220 to $600. These are the failures that stump generalists, so a specialist diagnosis is worth it. Call (855) 772-8171 for a free quote.
What does a full new automated gate installation cost in Pasadena?
A full new automated gate installation typically costs $3,500 to $9,000, covering the gate, the operator, the access control and the site work. A light residential gate sits at the low end; a heavy commercial gate with multiple entry points sits at the high end. Call (855) 772-8171 to price your job.
Can you come today?
Same-day service is often possible. Call (855) 772-8171 and we’ll book you into the next opening. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free.
Key Takeaways
- Residential gate motor replacement in Pasadena: $850 to $1,900 (swing) or $1,200 to $3,200 (sliding).
- Motor, board, sensor and access-system repairs: $150 to $700 depending on the part.
- Full new automated gate installation: $3,500 to $9,000.
- Repair usually beats replacement unless the operator is old and multiple parts are failing.
- We service nine major gate brands, so we work on your system, whatever it is.
If your gate motor or opener is failing, don’t wait for it to stop working entirely. Call Pasadena Gate Service at (855) 772-8171 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 15 years of experience, and every one of them is a gate specialist.
Pricing reflects the Pasadena market as of 2026. Pasadena Gate Service offers free estimates. Call (855) 772-8171.
Written by the team at Pasadena Gate Service.
What Our Customers Say
"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Erin Thompson"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Brooke Rhodes"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Danielle Sutton