Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Pasadena?
Gate installation in Pasadena typically costs $2,400 to $6,800 for a standard residential driveway gate with an automatic operator, and $1,100 to $2,600 for a single pedestrian or garden gate. Commercial and wide-span sliding gates run $7,000 to $18,000+, depending on width, material and access-control hardware. These are installed prices: gate, posts, hardware, operator and the wiring to get power to it.
Those ranges cover most of what we quote in Pasadena, but the number that matters is the one on your written estimate. We look at the opening, the soil, the power source and the gate type before we put a figure down. Our technicians have up to 15 years of experience, and the estimate is free.
Key Takeaways
- A standard residential swing or slide gate with an operator installed runs $2,400 to $6,800 in Pasadena.
- Pedestrian and garden gates are the cheapest to install, usually $1,100 to $2,600.
- Commercial and wide-access gates start around $7,000 and climb past $18,000 with access control.
- Power and conduit to the gate site is the most common surprise line item, often $400 to $1,800 on its own.
- The written estimate is the final price. We don’t quote over the phone and then adjust it on the day.
Gate Installation Cost Breakdown (2026)
Break the job into its parts and the total makes more sense. Here’s how the money usually splits for a residential automatic driveway gate in Pasadena. The gate leaf itself is rarely the biggest line – getting power and a solid footing to the opening often is.
| Line Item | Typical Range (2026) | What It Covers |
|---|---|---|
| Gate panel / leaf (steel, aluminum or wood) | $700 – $3,200 | Material and fabrication for a single-leaf gate sized to your opening |
| Posts, hinges and mounting hardware | $250 – $900 | Posts set to proper footing depth, hinges, rollers, brackets |
| Automatic operator (swing or slide) | $650 – $2,400 | Motor unit and arm or track assembly, sized to gate weight |
| Access control and safety devices | $300 – $1,600 | Keypad, remotes, photo eyes, loop detector, safety edges |
| Electrical run and conduit to the gate | $400 – $1,800 | Power from the panel to the operator, conduit, low-voltage wiring |
| Site prep, footing and concrete | $250 – $1,100 | Excavation, footing pour, leveling, cleanup |
| Labor and installation | $500 – $1,900 | Setting, hanging, aligning and commissioning the gate |
Pedestrian and garden gates usually land at $1,100 to $2,600 installed – no operator, smaller opening, simpler hardware. Commercial or wide-span sliding gates start near $7,000 and run past $18,000 once you add heavy-duty operators, vehicle loop detectors, card readers and the heavier posts a wide span needs.
What pushes a job toward the top of a range: an opening wider than about 12 feet, a heavy steel or solid-wood leaf, a gate that has to swing uphill, a long power run from the house, sloped ground that needs retaining work, and a commercial site that needs access control tied into an existing system. What keeps it lower: a standard-width aluminum gate, an operator matched to a light leaf, an existing power source close to the opening, and flat, easy ground to dig.
If you’re not starting from scratch, repairing an existing gate is almost always cheaper than a full install, and that’s a big part of what we do. If you already have a gate that won’t move, our Pasadena Gate Service covers the repair side first, so you know whether new hardware is actually needed before anyone quotes a replacement.
What Affects Gate Installation Pricing in Pasadena
- Gate type and material. A basic aluminum pedestrian gate is the cheapest option. A solid-wood driveway gate costs more in material and in operator capacity, because the motor has to move more weight and more wind load. Steel sits in between and lasts longer.
- Opening width and swing. Wider openings mean heavier panels, heavier posts and a larger operator. A gate that swings uphill needs a different operator and sometimes a different hinge setup, which adds to the job.
- Power and conduit distance. If the gate is far from the electrical panel, trenching and conduit add up fast. This is the single most variable line in a Pasadena quote, because lot layouts vary so much from one property to the next.
- Automatic vs. manual. A manual gate needs no operator and no power run, which saves a big chunk of the total. An automatic gate adds the motor, the safety devices and the wiring – and that’s where a lot of the value sits, since most people install a gate to control vehicle access without getting out.
- Access control complexity. A single keypad and two remotes is one thing. A system with vehicle loop detectors, card readers, intercom and integration into an existing access platform is another. Multi-tenant HOA and commercial sites fall here.
- Soil and site conditions. Posts have to go to proper footing depth for the gate to stay true. Pasadena’s clay-heavy ground holds water and shifts with the seasons, so footing design matters and can affect both the dig and the concrete volume. Flat, open ground is simpler than a tight corner with root intrusion.
One more factor that costs nothing to check: brand. If you’re adding a gate where an operator already exists, or you want the new unit to match hardware elsewhere on the property, we service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. We work on your brand, whatever it is. That matters because the brand on the gate doesn’t dictate the price of the install, but it does dictate what we can reuse and how we plan the wiring.
How to Save on Gate Installation
You can’t cut the price of a gate install without cutting something real, but a few choices reliably lower the total.
- Keep the opening standard. A gate sized to a common width costs less than one fabricated to an odd span. If you have flexibility on the opening, use it.
- Match the operator to the leaf, not oversize it. Buying a bigger motor than the gate needs adds cost without adding life. A correctly sized operator on a light gate performs better than an oversized one on a heavy gate.
- Put the gate near power if you can. Every extra foot of conduit is money. If there’s a choice about where the gate goes, put it close to the panel.
- Reuse what’s sound. If existing posts, hinges or an operator are in good shape, we’ll tell you. Diagnosis first, solution second – we don’t sell a replacement where a repair is the right call.
- Plan access control for now, not for someday. Adding a keypad and photo eyes during the install costs less than retrofitting them a year later, and it’s the safety piece that matters most on an automatic gate.
- Get a written estimate before any work starts. That’s how you compare two quotes fairly. The estimate is free, and the number in writing is the number we stand behind.
Call (855) 772-8171 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What’s Included in a Gate Installation Quote
A good quote for a gate install in Pasadena should spell out seven things: the gate panel and material, the posts and hardware, the operator if one is included, the access and safety devices, the electrical run and conduit, the footing and concrete, and the labor. If a quote is a single number with no breakdown, ask for one. It’s the only way to know whether the cheaper bid is actually cheaper or just missing the power run.
Two things regularly get left out of low bids. First, safety devices. An automatic gate that can crush or trap needs photo eyes, safety edges or a loop detector, and skipping them is a liability issue, not a saving. Second, the footing. Posts set shallow will lean within a season or two, and re-setting them costs more than doing it right the first time. We price both into the estimate so nothing gets added later.
The same rule applies to the operator wiring. High-voltage connections and the low-voltage control wiring both need a proper install, and an operator tied in without correct grounding or fuse protection is a call-back waiting to happen. We plan the electrical side as part of the install, not as an afterthought.
Repair or Replace: Which Makes Sense?
It’s usually cheaper to repair an existing gate than replace it, unless the gate leaf, posts or operator are beyond saving. A gate that has stopped moving because of a failed operator, a dead control board or a misaligned sensor is almost always a repair, not a replacement. That’s Pasadena gate work we do every week: motor, control board, loop detector and access-system failures that a generalist can’t diagnose.
Replace when the posts are rotten or leaning, the gate leaf is bent or rusted through, or the gate is undersized for the opening and the operator keeps burning out because of it. If two of those are true at once, a new install is the better spend. If none of them are, repair is. We tell you which before we quote anything, and the answer comes from looking at the gate, not from a sales target.
Safety on Automatic Gates
An automatic gate moves a heavy barrier with a motor, and the parts that hurt people are the operator’s power and wiring, the weight of the gate panel itself, and a slide gate coming off its track. That’s why safety devices are part of the install, not an option. Photo eyes, safety edges and loop detectors are what stop the gate when something is in the way, and they need to be positioned and tested on site.
We handle the electrical and control side of gate work as trained technicians. We don’t walk homeowners through wiring an operator or adjusting high-voltage connections – those are jobs for someone trained to do them, and a mistake can cause serious injury. If your gate has a fault in the operator or its power, that’s a call to us, not a DIY project.
Why Choose a Gate Specialist for Your Install
Gate installation is a small slice of what a general contractor or garage-door company does, and it’s the whole job for us. We handle gate repair, electric gate repair and new installation, so the same team that hangs and commissions your gate is the one you call when it needs service later. You don’t need a second vendor when the gate’s needs change.
That focus shows up in diagnosis speed. Our technicians have up to 15 years of experience, and they arrive familiar with the system on site – whether that’s a LiftMaster swing operator, a FAAC slide unit, a DoorKing access system, or a Ghost Controls or Mighty Mule residential operator. We’re brand-agnostic. Technicians are trained on your existing system, not pushed toward a preferred brand. That means fewer replacements you don’t need and a faster path to a working gate.
Electric gate repair is a core competency here, not an add-on. Motor, control board, loop detector and access-system failures are the work we do, and it’s the reason a stuck gate or a full install both land on the same call.
FAQs – Gate Installation Cost
How much does gate installation cost in Pasadena?
Gate installation in Pasadena typically costs $2,400 to $6,800 for a standard residential automatic driveway gate, and $1,100 to $2,600 for a pedestrian or garden gate. Commercial and wide-span gates run $7,000 to $18,000+. Call (855) 772-8171 for an exact quote – estimates are free.
How much does an automatic gate operator add to the price?
An automatic operator typically adds $650 to $2,400 to a residential install, and the electrical run to power it adds $400 to $1,800 more. A manual gate skips both. Call (855) 772-8171 and we’ll price the operator that fits your gate.
Is it cheaper to repair or replace a gate?
Repair is usually cheaper – often a fraction of a new install – unless the posts, leaf or operator are beyond saving. A failed operator, control board or sensor is a repair. Rotten posts and a bent leaf together usually mean replace. Call (855) 772-8171 for a free estimate and we’ll tell you which is the right call.
Can you install a gate the same day?
Same-day service is available, though a full gate install usually needs a scheduled visit once the gate and hardware are ready. Repair calls are the ones we can often turn around same day. Call (855) 772-8171. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Do you work on the brand of gate I already have?
Yes – we service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule, and we work on your brand, whatever it is. That means we can often install a new gate around an existing operator rather than replace it. Call (855) 772-8171 to talk through what you have.
What’s the biggest surprise on a gate installation quote?
The electrical run and conduit – typically $400 to $1,800 – because it depends entirely on how far the gate is from your panel. Safety devices and footing are the other two line items that show up on a real quote and go missing on a low bid. Call (855) 772-8171 for a written estimate that spells out every line.
Get a Free Gate Installation Estimate in Pasadena
Whether you’re putting in a new driveway gate, upgrading a manual gate to automatic, or fixing a gate that’s stuck, call (855) 772-8171 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We look at the opening, the power and the gate type before we put a number down, so the written estimate is the price you pay. Gate specialists, not generalists – from a stuck gate to a full installation, one call covers it.
Pricing reflects the Pasadena market as of 2026. Pasadena Gate Service offers free estimates – call (855) 772-8171.
Written by the team at Pasadena Gate Service.
What Our Customers Say
"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Erin Thompson"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Brooke Rhodes"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Danielle Sutton